Your home deserves wiring that's safe and up to code, and that starts with calling someone who can scope the job before anything is scheduled. Spokane Valley Electrical Company handles the full range of electrical work for homes and businesses across Spokane Valley and Spokane County: from a dead outlet or a tripping breaker to a full panel upgrade or a whole-home rewiring project. We service this area, and its neighborhoods each have their own wiring. Older bungalows near the valley floor, mid-century ranches, newer construction out toward Liberty Lake - each one brings its own panel type, its own wiring era, and its own set of considerations. We show up ready to work.
Whether you need a residential electrician for a straightforward repair or a commercial electrical contractor for a larger installation, the process is the same. You call, we scope the job on the phone, and you get a price before anything is booked.
Electrical work like this comes up more than people expect, and it rarely arrives at a convenient time. A flickering light that turns out to be a loose connection in the panel. A dead outlet in a kitchen that trips the GFCI every time it resets. A burning smell near a switch plate that needs to be traced before anyone uses that circuit again. Sparking outlets, breakers that won't hold, circuits that go dark without explanation: these are the kinds of problems we handle, for homeowners and commercial tenants alike.
We give straight answers about your panel and wiring. If a repair is the right call, we say so. If something needs more attention, we tell you that too, before any work starts.
On the installation side, the scope is just as broad. Outlets and switches, indoor and outdoor lighting, recessed and LED fixtures, ceiling fans, GFCI and AFCI protection, dedicated appliance circuits, exterior lighting for garages and outbuildings - all of it falls within what we handle for both residential and commercial properties. We'll trace it, fix it, and test it before we leave.
Spokane Valley's housing stock spans a wide range of eras, and that range matters when it comes to electrical work. Homes built in the 1940s through the 1960s may still have original wiring configurations that were standard at the time but no longer meet current code. Some of those properties still have knob-and-tube wiring in the walls or aluminum branch-circuit wiring from the 1960s and 1970s, both of which carry specific risks and specific remediation requirements.
Panels from that same period were often sized for loads that look nothing like a modern household's draw. A 60-amp or 100-amp service that was adequate for a home with no air conditioning, no electric vehicle, and no high-draw kitchen appliances may not carry today's load safely. Knowing what to look for in a panel from a given decade, and knowing which wiring types are common in which parts of the valley, changes how a job gets scoped and what questions get asked on the initial call.
We know schedules shift, so we keep booking flexible, and that matters most when a larger project is involved. A panel upgrade or a whole-home rewiring job is not a one-call fix, and getting the scope right before anything starts is what keeps the work on track.
A panel upgrade becomes necessary when the existing service can no longer carry the load safely. Breakers that trip under normal use, a panel that runs warm to the touch, a fuse box that has not been touched since the house was built - these are the signs that the service needs attention. A 100-amp to 200-amp upgrade involves replacing the panel, upgrading the service entrance and meter connection, and confirming that grounding and bonding meet current code. Where a subpanel is needed to serve a detached garage or a finished basement, that work is scoped as part of the same conversation.
Rewiring projects range from replacing a single outdated circuit to a full whole-home rewiring. Knob-and-tube replacement and aluminum wiring remediation are both jobs we handle, and both require a clear-eyed assessment of what is in the walls before any work is quoted. Arc-fault and ground-fault breakers are installed as part of the upgrade where code requires them, and load calculations are part of how we confirm the new service size is right for the property.
A plain answer on repair versus upgrade is part of every call. If the panel can be repaired, we say so. If it cannot, we explain why, and you decide how to proceed. Dependable service. A price agreed before we start. Local know-how.
Ready to get the power back on? For a lot of Spokane Valley properties, that question has taken on a new meaning as the electrical demands on a home or business have grown. EV charger installation is one of the most common requests we handle right now. A Level 2 home EV charger requires a dedicated 240-volt circuit, and in older homes, that often means a panel assessment before the circuit is run. We handle the circuit, the breaker, and the outlet or hardwired connection, and we confirm the panel has the capacity to carry the new load before anything is scheduled.
Backup generator hookups are another area where we see steady demand. Spokane County winters can put pressure on the grid, and a generator transfer switch installation is the right way to connect a backup generator safely - without backfeeding the utility line. We handle the transfer switch and the circuit side of the connection.
Whole-home surge protection is a straightforward addition at the panel that protects connected equipment from voltage spikes, and it is something we install as a standalone job or as part of a larger panel project. Outdoor and weatherproof outlet installation, wiring for home additions, garage electrical work, and basement circuit installation round out the kind of modern-load work we handle across the area. Wiring work checked against code before sign-off is part of every job, not an afterthought. We'll handle the wiring so you don't have to.
Electrical work like this comes up more than people expect when a property changes hands, when a renovation is being planned, or when something in the panel has been flagged by an insurance carrier. A home electrical inspection covers the panel, the branch circuits, the grounding and bonding, and the condition of outlets and switches throughout the property. We look at what is there, note what does not meet current code, and give you a plain account of what the inspection found.
GFCI and AFCI protection are two of the most common safety upgrades that come out of an inspection. Kitchens, bathrooms, garages, and outdoor circuits are required to have GFCI protection under current code, and many older Spokane Valley homes were wired before those requirements existed. Arc-fault breaker installation is a similar upgrade for bedroom and living-area circuits. Neither is complicated to add, and both address real risks.
We protect your floors and finishes while we work. That means drop cloths where needed, care around finished surfaces, and cleanup before we leave. Permit requirements vary by job type and by jurisdiction, and we confirm what applies before any work is scheduled. We tell you if a permit is needed. We name the fault plainly. You decide the fix.
Electrical work like this comes up more than people expect, and the first question is almost always about cost. The straightforward answer is that the price is confirmed on the call, before anything is scheduled. You describe the situation, we scope the job, and you get a rate that covers what the work involves. There is no ambiguity about what is included, and the same number that books the job is the number to call with any question afterward.
We are available every day from 7:00 AM to 8:30 PM. Urgent electrical faults - a panel that has gone dead, an outlet that is sparking, a breaker that will not reset - are the calls we take seriously within those hours. If you are dealing with something that cannot wait, call and tell us what is happening. We will tell you what the schedule allows and what the next step looks like.
For larger projects, the scoping conversation takes a little longer, but the structure is the same. The price is set before the work starts, the scope is clear, and you know what you are agreeing to before anyone shows up at the property. Call and we'll get you back to full power.
We work across Spokane Valley and throughout Spokane County, covering both residential and commercial properties. That includes Spokane, Liberty Lake, Millwood, Veradale, Otis Orchards, and Greenacres, along with the surrounding communities in the county.
The work is the same whether the property is a single-family home, a rental unit, a retail space, or a commercial building. The job gets scoped on the call, the price is confirmed before anything is scheduled, and the work is carried out to the code that applies in this area.
Spokane Valley's housing stock covers a wide range of construction eras, and older homes in the area commonly have wiring configurations that require specific handling. Knob-and-tube wiring, aluminum branch-circuit wiring from the 1960s and 1970s, and panels sized for loads that look nothing like a modern household's draw are all things we see regularly in this area. Knowing what to look for in a home from a given decade changes how a job gets scoped and what questions get asked on the initial call.
We start every job by tracing the fault, not listing everything that could theoretically be improved. If the repair is the right call, we say so. If something else needs attention, we explain what it is, why it matters, and what the options are. You get a plain answer on repair versus upgrade, and you decide how to proceed.
After completing the work, we test the circuit, the devices, and the protective equipment before we call the job done. Wiring work is checked against code before sign-off. If something does not pass the test, we address it on the same visit before we leave the property.
Note which room or circuit is affected, whether the problem is constant or intermittent, and whether anything unusual happened before it started, such as a storm, a tripped breaker, or a new appliance being plugged in. If there is a burning smell, a warm outlet, or a visible scorch mark, note that too. The more specific you can be, the more accurately we can scope the job on the call.
Call us at (509) 566-9799 and describe what you are seeing.
We will ask about the symptoms, compare them to what was found on the original visit, and determine whether the issue is related to the work that was done or something separate. If the original fault was not fully resolved, we treat it as a continuation of the same job.
Ask what the job involves, what the price covers, whether a permit is required, and what to expect from the visit. Those are the questions we answer on every call before anything is scheduled. If you have a specific concern about the wiring in your home or the condition of your panel, raise it on the call and we will address it directly.
When you call and book, we confirm the date, the time window, the scope of the work, and the price before the call ends. If anything changes on our end, we contact you before the appointment. We recommend keeping the number you called from available in case we need to reach you before the visit.
If we find something on the visit that changes the scope, we stop and explain what we found before proceeding. You get a clear account of what the additional work involves and what it will cost. Nothing is added to the job without your agreement first.
Electrical work like this comes up more than people expect, and the right move is to get the scope clear before anything else. Spokane Valley Electrical Company handles repairs, panel upgrades, rewiring, EV charger installation, generator hookups, safety inspections, and the full range of electrical work for homes and businesses across Spokane Valley and Spokane County.
We are open every day from 7:00 AM to 8:30 PM.
Call (509) 566-9799 for a quote on any electrical job, large or small.
We tell you if a permit is needed. We name the fault plainly. You decide the fix.
(509) 566-9799